Contextual Info:  search PRODUCT INFO TinkerKit Blue Led [5mm] Code: T010111 The LED is possibly the simplest actuator available. It’s a low power light source available in many colors. It lights up when powered from an Arduino pin. Input: Arduino provides a maximum of 40 mA per pin; this is enough

Contextual Info:  PRODUCT INFO TinkerKit Linear Potentiometer Code: T000150 A Linear Potentiometer is a commonly used variable resistor. It can often be found as a volume controller on radios and TVs. By moving the slider you can vary the output voltage between 0 and 5V. This value

TINKERKIT LDR SENSOR

Contextual Info:  PRODUCT INFO TinkerKit LDR Sensor Code: T000090 LDR or Light Dependant Resistor, or Photoresistor is a variable resistor. Light falling on the sensor decreases its resistance. Output: This module outputs 5v when the sensor receives no light (the circuit is open) and 0v when exposed to bright light (the circuit is

Contextual Info:  search PRODUCT INFO TinkerKit Thermistor Module Code: T000200 The Thermistor is a resistor whose resistance varies significantly more than in standard resistors with temperature. Output: This module's output approches 5v as the temperature increases. As the temperature decreases, it approaches 0V. When

Contextual Info:  PRODUCT INFO TinkerKit Rotary Potentiometer Code: T000140 A Potentiometer is a commonly used variable resistor. Turning the knob, you vary the output voltage between 0 and 5V. This value is sent through the middle pin of the pot. Output: This module outputs 5v when turned in one direction, and 0v

Contextual Info:  search PRODUCT INFO TinkerKit PushButton Code: T000180 The Pushbutton Module is possibly the simplest sensor available. It detects when a person or an object presses on its circular cap. Output:This module outputs 5v when the button is pressed and 0v when

Contextual Info:  PRODUCT INFO TinkerKit Joystick Code: T000030 The Joystick module is similar to analog joysticks found in gamepads. It is made made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.

ARDUINO UNO REV3 - RETAIL

Abstract: BCM43362 Futaba 5 lt 51 Mediatek Gps Mt3329 T010010 Arduino Mega2560 XBee-PRO s1 PIC24F16ka102 Free Projects futaba transmitter parallax servo controller
Contextual Info: EMBEDDED SOLUTIONS Wireless Solutions Anaren . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 6 Antenova . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Atmel . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Bluegiga . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Contextual Info: TinkerKit Tilt Sensor Overview The Tilt Sensor can detect when it is at an angle. Output: This module contains two contacts and a small metal ball. When the sensor is in its upright position, the ball bridges the two contacts, completing the circuit. When the board is tilted, the ball

Contextual Info:  search PRODUCT INFO TinkerKit Touch Sensor Code: T000220 The Touch Sensor is sensitive to skin contact. Output: This module normally outputs 0v, but when touched, sends 5v. When connected to an input on the Arduino using the TinkerKit Shield, you will see 0 when there is no touch, and 1023 when touched.

Contextual Info:  PRODUCT INFO TinkerKit Hall Sensor Code: T000070 A Hall sensor creates a voltage related to the magnetic field around the sensor. This can be used to detect distance from a nearby magnet. Hall sensors can also be used to detect the magnetic field induced in a wire

Contextual Info:  PRODUCT INFO TinkerKit 2/3 Axis Accelerometer Code: T000020 An accelerometer is a device that measures acceleration. It is very common in consumer electronics such as portable electronic devices and video game controllers to detect movement using accelerometers.